case cvx's

Discussion in 'Machinery Matters' started by headcase, Nov 11, 2010.

  1. go diego go

    go diego go Well-Known Member

    Joined:
    Feb 14, 2010
    Messages:
    127
    Wha5 sort of price were they? Thanks
     
  2. Merv_B

    Merv_B Well-Known Member

    Joined:
    Jan 12, 2010
    Messages:
    7,671
    Location:
    Wexford
  3. Win

    Win Well-Known Member

    Joined:
    May 14, 2015
    Messages:
    4,788
    Location:
    herefordshire
    £200, depends on exchange rate at the time a bit.
     
    TimN likes this.
  4. YELROM

    YELROM Active Member

    Joined:
    Feb 15, 2013
    Messages:
    33
    @Win i don't know if you saw this post but the error code on my spool is 82

    Also my front suspension is now not working, the suspension goes up and down with switch on the dash, but the green suspension light is not coming on on the lcd pillar
    Wondering if i should try swapping the front axle potentiometers with the ones on the TVT?
     
  5. Win

    Win Well-Known Member

    Joined:
    May 14, 2015
    Messages:
    4,788
    Location:
    herefordshire
    I must have missed that sorry, 82 is spool not in neutral or it thinks its not. Check plugs first I suppose, you can swap plugs round to see if problem moves or not, same switch will still work same valve.

    So if you lift it up to mid position on switch what happens when you drive off and it goes above 14k, does it drop back to the bottom or stay in mid position? Or if it was above mid position what would happen above 14k??
     
  6. Leinster restorer

    Leinster restorer New Member

    Joined:
    Aug 10, 2017
    Messages:
    1
    Did this solve your problem? I have a cvx 1170 with exact same symptoms as yours had. Do you remember how much the board was?
     
  7. YELROM

    YELROM Active Member

    Joined:
    Feb 15, 2013
    Messages:
    33
    Tried lowering the suspension today, i lowered it with the switch on the dash and it stayed down till i went over about 15k then it lifted itself to about mid position and stayed there but the suspension is not working

    Not had time to try swapping the spool wiring yet

    Also the external buttons for the front linkage don't work and it says in the manual about activating them but it doesn't seem to explain how to do it.
    I have tried swapping the buttons with the TVT so its not the buttons, do you have any idea why they might not work
     
  8. Win

    Win Well-Known Member

    Joined:
    May 14, 2015
    Messages:
    4,788
    Location:
    herefordshire
    So the suspension controller is working then, has the bulb gone in the light? Sounds like the accumulators are gone or out of gas if its at the mid position but no movement.

    Not sure about buttons, you'd think they would be activated if the linkage was on from new, are the plugs and wiring ok as in corrosion?
     
  9. YELROM

    YELROM Active Member

    Joined:
    Feb 15, 2013
    Messages:
    33
    The bulb hasn't gone as all the lights light up when you turn the ignition on and it works then

    It also has external buttons for the front spool and they done work either
    It was the other year when i swapped the buttons with the TVT but i don't remember them being corroded but will check
     
  10. Merv_B

    Merv_B Well-Known Member

    Joined:
    Jan 12, 2010
    Messages:
    7,671
    Location:
    Wexford
    Ptk44 and scoffcruddle like this.
  11. scoffcruddle

    scoffcruddle Well-Known Member

    Joined:
    Jan 30, 2011
    Messages:
    3,872
    Location:
    Lancashire
    Ptk44 and Merv_B like this.
  12. TimN

    TimN Active Member

    Joined:
    Jun 17, 2018
    Messages:
    27
    Location:
    Herefordshire
  13. TimN

    TimN Active Member

    Joined:
    Jun 17, 2018
    Messages:
    27
    Location:
    Herefordshire
  14. nashmach

    nashmach Well-Known Member

    Joined:
    Feb 22, 2010
    Messages:
    43,501
    Location:
    Wexford, Ireland
    TimN likes this.
  15. Win

    Win Well-Known Member

    Joined:
    May 14, 2015
    Messages:
    4,788
    Location:
    herefordshire
    I've never been photographed so many times in one week or ever!!!!
     
  16. Buster456

    Buster456 Member

    Joined:
    Jun 30, 2018
    Messages:
    8
    Hi I have just bought a 1190 and the front suspension doesn't seem to be working properly it activates and the green light comes on but the right hand side will drop. Does anyone no what could be causing this cheers
     
  17. Win

    Win Well-Known Member

    Joined:
    May 14, 2015
    Messages:
    4,788
    Location:
    herefordshire
    The green light is not flashing I take it? There's a rubber disk in the end of the top pin where the sensor fits that can wear, once it wears the suspension will move without moving the sensor. For instance if it needs to lower to keep the mid position it lowers but the sensor doesn't turn so it goes too low because the sensor signal hasn't changed to tell it where to stop. Remove cover on wishbone where wires go in, the sensor is bolted to a thin plate, the rubber disk is behind the thin plate and pushes in the end of the pin. It will look fine but try it on the sensor shaft and you will probably see its loose, once there's a some end float on the wishbone it accelerates the wear. In theory the sensor needs resetting once removed but mark its position on the thin plate before taking it off (slotted hole on sensor) and it may not throw a error when it goes back on.
     
  18. Buster456

    Buster456 Member

    Joined:
    Jun 30, 2018
    Messages:
    8
    Brilliant thankyou I will give that a go and see what happens cheers
     
  19. Win

    Win Well-Known Member

    Joined:
    May 14, 2015
    Messages:
    4,788
    Location:
    herefordshire
    Did you mean to put that in the ‘what annoyed you today’ thread?????:tt2:
     
    Arthur, nashmach, 100-90DT and 4 others like this.
  20. Big hit 199

    Big hit 199 Active Member

    Joined:
    Sep 19, 2016
    Messages:
    31
    Does anyone no of the part number for the stepper motor? Case part number or zf number? How much are you guys paying for them in your country? The dealer wants 8k New Zealand for them which seems like a complete rip off
    thanks
     
    TimN likes this.
  21. ShaneB140

    ShaneB140 Well-Known Member

    Joined:
    Dec 22, 2013
    Messages:
    722
    Location:
    Co Waterford
    @Win
     
  22. Win

    Win Well-Known Member

    Joined:
    May 14, 2015
    Messages:
    4,788
    Location:
    herefordshire
    Well they're £4k off Linde here in the UK which is roughly the same as off CNH. Briezlec in France were about half that a few years ago but don't know what they are now!
     
    gone likes this.
  23. Arthur

    Arthur Well-Known Member

    Joined:
    Jan 10, 2013
    Messages:
    16,469
    Location:
    Munster
    If you can get the part number try putting it in here...https://www.readygoparts.com/collections/tractor-parts
     
  24. johndeere6920s

    johndeere6920s Well-Known Member

    Joined:
    Jun 21, 2013
    Messages:
    14,174
    Location:
    south west ireland
  25. Ptk44

    Ptk44 Well-Known Member

    Joined:
    Jun 21, 2012
    Messages:
    1,841
    Location:
    Kildare Ireland

Share This Page