6600
Well-Known Member
Yes.Can you get away without them
Yes.Can you get away without them
Can you get away without them
I think they might be for drier countries with lower volumes going through .Can you get away without them
Like wexico??I think they might be for drier countries with lower volumes going through .
Can you get away without them
Perfectyes. Drum flat out for wb.
The plates are on the original concave but rarely on a replacement.
If your In bother with awns tighten the back of the concave 2mm more than the front on the threaded bar
:curse:Like wexico??
Are there sensitivity setting adjusters on the control panel?Grain loss monitor on a Deutz starline have not worked since I bought it and if it doesn't cost me a fortune I'd like it working. Dials are integrated into the dash, so I assume it is a factory fit. Tube at the back has slight dents needle never moves. If you drop a bunch of keys on the plate at end of the walkers, the needle moves slightly. Cables look OK. Any advice welcome, or a contact who could service it.
I have a similiar issue on the tx, when the paddles are plugged into a laptop and you tap them an electric impulse shows up, however when plugged into the monitor there isn’t a best off it, even got a second monitor off BB but no luckGrain loss monitor on a Deutz starline have not worked since I bought it and if it doesn't cost me a fortune I'd like it working. Dials are integrated into the dash, so I assume it is a factory fit. Tube at the back has slight dents needle never moves. If you drop a bunch of keys on the plate at end of the walkers, the needle moves slightly. Cables look OK. Any advice welcome, or a contact who could service it.
Yes, fiddling makes no difference.Are there sensitivity setting adjusters on the control panel?
Douglas Kidd is the man for that , I think he trades under WextecGrain loss monitor on a Deutz starline have not worked since I bought it and if it doesn't cost me a fortune I'd like it working. Dials are integrated into the dash, so I assume it is a factory fit. Tube at the back has slight dents needle never moves. If you drop a bunch of keys on the plate at end of the walkers, the needle moves slightly. Cables look OK. Any advice welcome, or a contact who could service it.
For some reason the wextec site is not working but he can be contacted under Kidd lubricants. He would sort it no bother.Douglas Kidd is the man for that , I think he trades under Wextec
I was just looking at that on DD myself nash :Thumbp2:. A very tidy looking example. She'd look very well in Wexico.
Did you fit new fingers along with new blade sections? Was the blade free to slide when refitted? You may need to set the height of some of the fingers if they’re not all perfectly level.Tomorrow is the day, put the new knife in this eve and put it going and bang bang bang, bent fingers I assume, have to go messing with them now in morning
No the fingers are all the ones that were on it, slid in free enough, the occasional bang to get it passed. I can see a couple of fingers are bentDid you fit new fingers along with new blade sections? Was the blade free to slide when refitted? You may need to set the height of some of the fingers if they’re not all perfectly level.
Are the fingers actually bent or is the slide slightly higher or lower on a few of the finger pairs?No the fingers are all the ones that were on it, slid in free enough, the occasional bang to get it passed. I can see a couple of fingers are bent
As in the gap in the fingers? :scratchhead: you can see some sections are touching the top and some touching the bottom of the gap in fingersAre the fingers actually bent or is the slide slightly higher or lower on a few of the finger pairs?
No, if you remove the blade, at the back of the fingers where the rear of the blade slides these may be up and down a bit. It can happen with poorly cast new fingers. Only cure is to remove them and pack above or below the bracket where necessary with tinfoil to level them out.As in the gap in the fingers? :scratchhead: you can see some sections are touching the top and some touching the bottom of the gap in fingers
Went perfect it seems to be running very well. 2 retractable fingers broke alright but that’s the only issues I hadGreat stuff Massey good to see you up and running. Did she go all right?