eddie86
Well-Known Member
Would it be black if it was a 03?
Absolutely. IMO.Would it be black if it was a 03?
Our ts definitely was and it was 02Would it be black if it was a 03?
Slow to drop could be from partly seized at the base of the ram, usually most affected in the upper part of the arm position, this will only show with no weight on the arms.Got a red T7 210 here and the arms haave gotten slower to raise but very slow to drop even with drop rate up full. Sometimes its ok and then most others its slow.
Any ideas?
Linkages are kept well greased where should be and its even slow to drop with weight on them.Slow to drop could be from partly seized at the base of the ram, usually most affected in the upper part of the arm position, this will only show with no weight on the arms.
No greasing point at the base of the lift rams and they have to pivot slightly.Linkages are kept well greased where should be and its even slow to drop with weight on them.
I remember you gave me the heads up when I asked about removing the assistor rams for doing the brakes on the 6070, took half a day to do the brakes, took near 3 days of rooting to free up and fit grease niples to the base of the ram. The T6 is getting daily shots of WD-40 to hopefully save the same rooting 🤦.No greasing point at the base of the lift rams and they have to pivot slightly.
Ok, thank you. I will have a look there and see.No greasing point at the base of the lift rams and they have to pivot slightly.
It won't affect lifting, how is it behaving when using the spool valves, if they are gone slow your pump might be the problem.Ok, thank you. I will have a look there and see.
This wouldn't make the arms sluggish to lift too though would it?
A beauty, she’d be great company for the 6640.Tractors Ads For Sale in Ireland | DoneDeal
Discover 6,502 Ads in Tractors For Sale in Ireland on DoneDeal. Buy & Sell on Ireland's Largest Tractors Marketplace.www.donedeal.ie
Might be of intrest to someone. A rarity in that condition I'd say
Have error codes 31 and HL on lift on the 8340. Any ideas ? Was going to try a potentiometer have cleaned earth on top of lift cover as was bit scabby and calibrated it a few times as it will work for a while once calibrated.
Id be a massey man but them nh's are nice. An ideal farmers tractor.A beauty, she’d be great company for the 6640.
Same as, they are much better than the small 42/43's (I have a 4345). Borderline too small if you are handling many bales of silage I think. The 54's are probably better than the T50's, especially the heavier ones and T3 onesId be a massey man but them nh's are nice. An ideal farmers tractor.
HL is height limit error as far as i know which made me think could be potentiometer possibly.31 is chassis harness disconnected.I'd say you've a bad connection at a multiplug. HL...never seen it before and it's not in the manual.
Have a 4355 here with a loader as well. Have the gits of a 1 tonne weight for the back of her as they need it for handling ales etc. Would the T50's be that much heavier?Same as, they are much better than the small 42/43's (I have a 4345). Borderline too small if you are handling many bales of silage I think. The 54's are probably better than the T50's, especially the heavier ones and T3 ones
I have 850 on the back of mine and it turns it inside out, I will go for more weight if I don't change it though.Have a 4355 here with a loader as well. Have the gits of a 1 tonne weight for the back of her as they need it for handling ales etc. Would the T50's be that much heavier?
Tractors Ads For Sale in Ireland | DoneDeal
Discover 6,502 Ads in Tractors For Sale in Ireland on DoneDeal. Buy & Sell on Ireland's Largest Tractors Marketplace.www.donedeal.ie
Might be of intrest to someone. A rarity in that condition I'd say
From my research, I have not driven one, the 5050/60/70 are a little over 500kg heavier than the MF4235-4355. I would tend to agree with @Bot.exe that they are well ahead of the above Masseys but slightly behind the 5455.Have a 4355 here with a loader as well. Have the gits of a 1 tonne weight for the back of her as they need it for handling ales etc. Would the T50's be that much heavier?