Todays Photo

[nashmach]

I could see it off in the distance your way and over to Kilmore. See the video of the Quay in New Ross?

Only downside is the tourist traffic.

I sure did, biblical.

 

[nashmach]

Not today's photo but as the old saying goes we have our gentleman's family, broke out the good stuff to mark the occasion.
View attachment 111844View attachment 111843

Congrats to you and the family Enda!

 

[KTM 450]

Not today's photo but as the old saying goes we have our gentleman's family, broke out the good stuff to mark the occasion.
View attachment 111844View attachment 111843

Congrats on the new arrival and the rest of your family.
May ye’r joys be as many as sheep in the glen and her worries as few as teeth in a hen.

 

[gone]

Congratulations @Endah

 

[josh]

Congrats and welcome to the world

 

[Blackwater boy]

 

[c4l]

Steering axle would save a lot of rubber
View attachment 111490

see that a lot down at the port. even with the triple axles with the single axle steering, just see the front 2 axles go opposite directions

 

[johndeere6920s]

Some tanker

 

[Danielk]

Doing my bit to save the world

 

[mixed fleet]

Tackled the main crop this week. Never fails to yield well. A bit like the tillage men I'm chopping most of it. Couldn't be arsed haggling for a tenner a bale.

 

[josh]

Some tanker View attachment 111861

Looks like some load of shite.

 

[scoffcruddle]

They were made for each other.😍🥰😍

 

[AYF]

They were made for each other.😍🥰😍View attachment 111913

Finally got the trailer?
Or has it been with you a while?

 

[scoffcruddle]

Finally got the trailer?
Or has it been with you a while?

I’ve had it since October I think,it’s very rarely idle,carted 500t of stone with it last week alone.

 

[marco]

Tackled the main crop this week. Never fails to yield well. A bit like the tillage men I'm chopping most of it. Couldn't be arsed haggling for a tenner a bale.
View attachment 111908View attachment 111909

Get some slurry on it if you can, will knock back the rushes abit

 

[bagenal]

Doing my bit to save the world


View attachment 111907

That looks a brilliant job, certainly way better than what I've seen other machines do around.

 

[c4l]

 

[d8666]

Tow bar on a 20.

 

[MeathMassey3]

Tow bar on a 20.View attachment 111976

He must be going to pull start it

 

[c4l]

are you popping into kirby's?

ahh jaysus, be really spoiled rotten if we went there on a thursday afternoon
was on the way to cullinanes and see if the mechanic was about. got the tm sorted in the end. the magnet/electric part of a solenoid down the side of the gearbox had gone bad. had to buy a whole new solenoid just to get the cap. aint cheap i tell ya

 

[Jay Dee]

Can you leave me 60 bales of straw round? No bother

 

[massey 6480]

Have you a steering axle or steering drawbar on your wilson .

Can you leave me 60 bales of straw round? No bother
View attachment 112008

View attachment 112007

 

[Jay Dee]

Have you a steering axle or steering drawbar on your wilson .

Both.

 

[massey 6480]

Which is of more benifit do you think .

Both.

 

[Jay Dee]

The drawbar, but both work together, can spin round as tight as I want,
One of our bits is tight access I can only come out 1 way, so I go up the road to a corner & spin round in the middle of the corner, wouldn't have a hope with a trailer.