What are you up to in the workshop?

[towbar]

Got caught out with an old amazone last week was in field beside house and went in for cup of tea and one of the rams must have being leaking a bit leaving the fertilizer dribble out on ground. 😂.

 

[c4l]

Got caught out with an old amazone last week was in field beside house and went in for cup of tea and one of the rams must have being leaking a bit leaving the fertilizer dribble out on ground. 😂.

at least it was in the field. got caught a few times not closing the spinner when filling in the yard

 

[johndeere6920s]

Does it have to be replaced with new so?
It's only for opening the fert spreader.
Might dig out a spring.

Yeah it would unfortunately I don't know why they do that.
I think there spun on a lathe and the head of them is sealed.
There's a one the same set up as yours on the transmission of the cvx's and it's 800 euro.
What size is that one it will say it on it somewhere

 

[Green Grass]

Them amazone are a bastard for the shutter opening up ,they are some engineers .in my rauch the hyd. pressure on the shutter is to close so it could close unknown to you but there is a valve fitted where you hook up to tractor to stop this

 

[c4l]

Them amazone are a bastard for the shutter opening up ,they are some engineers .in my rauch the hyd. pressure on the shutter is to close so it could close unknown to you but there is a valve fitted where you hook up to tractor to stop this

The MDS is the same here. Have single acting rams on it and it used to open up. Dad rigged a valve into the mix and used a t joint so both rams working on one spool and when its closed we shut the valve to keep it that way

 

[towbar]

A claas screen worked on a year ago and the new bulb failed possibly cheap rubbish or possibly faulty driver chip anyway broke the replacement while fitting it so brainwave used a strip of led lights instead. Worked nicely and should be a lot more reliable.

 

[Ptk44]

A claas screen worked on a year ago and the new bulb failed possibly cheap rubbish or possibly faulty driver chip anyway broke the replacement while fitting it so brainwave used a strip of led lights instead. Worked nicely and should be a lot more reliable.

Nice work

 

[c4l]

A claas screen worked on a year ago and the new bulb failed possibly cheap rubbish or possibly faulty driver chip anyway broke the replacement while fitting it so brainwave used a strip of led lights instead. Worked nicely and should be a lot more reliable.

should be our own version of david king

 

[towbar]

should be our own version of david king

I wish but I just don’t know how he gets access to all the circuit diagrams and components. I can do the simple power supply stuff and lighting etc but not the more complex stuff.

 

[eddie86]

Yeah it would unfortunately I don't know why they do that.
I think there spun on a lathe and the head of them is sealed.
There's a one the same set up as yours on the transmission of the cvx's and it's 800 euro.
What size is that one it will say it on it somewhere

That's some price for it.
This one is:
0.16L
80bar
Max 210 bar
Max temp 80°C

Edit. I assume it's 8.0 and 12.0 bar.

 

[lough]

Can you re-pressurise these bottles or how is it done?View attachment 89966

Could you convert it to a handle and open it by hand or would it not be practical

 

[eddie86]

Could you convert it to a handle and open it by hand or would it not be practical

You could but it would be a backward move imo.
I'm sure a spring will get it going again.

 

[MF30]

You could but it would be a backward move imo.
I'm sure a spring will get it going again.

There were two springs on the one here and no nitrogen accumulator.

 

[towbar]

Trying to remove the pins gas and bottle jack. Switched to grinder and will be followed by mag drill!! Much more effective

 

[Mid cork]

Trying to remove the pins gas and bottle jack. Switched to grinder and will be followed by mag drill!! Much more effective

Did you try putting a bolt or a threaded into the pin and using it as a pullers. With that and the gas you would shift most of them.

 

[Ptk44]

Trying to remove the pins gas and bottle jack. Switched to grinder and will be followed by mag drill!! Much more effective

That is pure hardship and yet can’t be avoided.

 

[Bog Man]

Trying to remove the pins gas and bottle jack. Switched to grinder and will be followed by mag drill!! Much more effective

I will drop the L 70 up to you in a fortnight.

 

[scoffcruddle]

I used to think JCB pins were bad to remove,Volvo pins are on another level of tight.

 

[Seedsower]

Trying to remove the pins gas and bottle jack. Switched to grinder and will be followed by mag drill!! Much more effective

Will they not be very hard for driĺling?

 

[towbar]

Will they not be very hard for driĺling?

No I tested with an ordinary drill bit before cutting

 

[towbar]

Did you try putting a bolt or a threaded into the pin and using it as a pullers. With that and the gas you would shift most of them.

I didn’t maybe I’ll try that on second one. Definitely going to try lifting second one out in place if possible.

 

[Bog Man]

Did you try putting a bolt or a threaded into the pin and using it as a pullers. With that and the gas you would shift most of them.

I did that and used the hub of a brake disc as the pulling point as it fitted over the head of the pin .

 

[towbar]

I did that and used the hub of a brake disc as the pulling point as it fitted over the head of the pin .

And? Did it work😀

 

[Endah]

I find the hollow cylinder is a gift for the likes of those jobs, You can have it set up and under pressure , heat the pin with the gas and 9/10 it'll pop and allow you to draw it out using the cylinder, a good constant force is hard bet vs sledging the life out of something.
That said you need a decent size of a thread in the pin to do this as anything below m10 is just going to get stretched if its well stuck.

 

[Bog Man]

And? Did it work😀

On the Z linkage it worked but not on the hinge point for the euro hitch.